SpeedTouch 510 wieder als Modem

[jutta]

bei "standard wiederherstellen" bin ich bei einem st 510 einmal eingefahren da waren nachher auch die templates und language files weg und ich musste das alles von der speedtouch setup-cd aus wieder reinspielen (und das funktionierte nur unter windows).

beim hw-reset werden einfach die defaults wiederhergestellt. das sollte funktionieren (sofern die defaults der oben genannten sw-version fuer single-user geeignet sind).

siehe auch http://xDSL.at/new/viewtopic.php?t=30996
und http://xDSL.at/phpbb2/viewtopic.php?t=30487

[Wooschli]

auch das mit dem reset hab ich schon versucht. der reset funktioniert auch wunderbar aber die Factory defaults sind nicht geeignet für single user betrieb.

werd nun mal einfach einen alte ini reinspielen. mal schaun was pasiert.

[Wooschli]

so hab das mit dem rückspielen der alten ini versucht aber ohne erfolg. nach einspielen der ini komme ich nicht mehr aufs Modem. Nicht mit der IP 10.0.0.138 oder der IP 192.168.1.254.

habe auch versucht die ini ST510_Austria_01.ini und die vom Modem nach dem Factory Default zu vergleichen. aber nach dem zurückspielen funktionierte wieder nichts. Modem mußte wieder resettet werden.

vielleicht hat wer lust mir die ini um zu schreiben oder zumindest es zu versuchen?

[Bender]

auch das mit dem reset hab ich schon versucht. der reset funktioniert auch wunderbar aber die Factory defaults sind nicht geeignet für single user betrieb.

Habe weder gehört, gelesen noch selbst erfahren (bei ST510v3/v4, 516v5, 716v5 WL), dass Factory defaults einen anderen als Modem-, also Single-User-Status herstellen. — Hier scheint's mit der VPN-Einwahl zu hapern bzw. eine LAN-interne Fehlkonfig von Fremdrouter zu ST510 gegeben zu sein.

[Wooschli]

so sieht die factory default ini aus:

[ cac.ini ]
config port=dsl0 state=enabled
config port=dsl1 state=enabled
config port=atm2 state=enabled
config port=aal5 state=disabled
config port=atm5 state=disabled
overbooking rt=0 nrt=0

[ language.ini ]
config language=en complete=no

[ script.ini ]
add name=autopvc_add_qos index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_qos index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_qos index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_delete_qos index=0 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_qos index=1 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_qos index=2 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_bridge index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_bridge index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_bridge index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_bridge index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_bridge index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_bridge index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 encaps $19 fcs $20 ulp mac"
add name=autopvc_add_bridge index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_bridge index=7 command="eth bridge ifadd intf _auto_$1_$2_eth dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_bridge index=8 command="eth bridge ifconfig intf _auto_$1_$2_eth"
add name=autopvc_add_bridge index=9 command="eth bridge ifattach intf _auto_$1_$2_eth"
add name=autopvc_delete_bridge index=0 command="eth bridge ifdetach intf _auto_$1_$2_eth"
add name=autopvc_delete_bridge index=1 command="eth bridge ifdelete intf _auto_$1_$2_eth"
add name=autopvc_delete_bridge index=2 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_bridge index=3 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_bridge index=4 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_bridge index=5 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_bridge index=6 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_bridge index=7 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_pppoerelay index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_pppoerelay index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_pppoerelay index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_pppoerelay index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_pppoerelay index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_pppoerelay index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 ulp mac"
add name=autopvc_add_pppoerelay index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_pppoerelay index=7 command="eth ifadd intf _auto_$1_$2_eth dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_pppoerelay index=8 command="eth ifattach intf _auto_$1_$2_eth"
add name=autopvc_add_pppoerelay index=9 command="ppp relay ifadd intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoerelay index=0 command="ppp relay ifdelete intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoerelay index=1 command="eth ifdetach intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoerelay index=2 command="eth ifdelete intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoerelay index=3 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoerelay index=4 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoerelay index=5 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=6 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_pppoerelay index=7 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_pppoerelay index=8 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_ipoa index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_ipoa index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_ipoa index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_ipoa index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_ipoa index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_ipoa index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 encaps $19 fcs $20 ulp ip"
add name=autopvc_add_ipoa index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_ipoa index=7 command="ip ifadd intf _auto_$1_$2 dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_ipoa index=8 command="ip ifattach intf _auto_$1_$2"
add name=autopvc_delete_ipoa index=0 command="ip ifdetach intf _auto_$1_$2"
add name=autopvc_delete_ipoa index=1 command="ip ifdelete intf _auto_$1_$2"
add name=autopvc_delete_ipoa index=2 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_ipoa index=3 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_ipoa index=4 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_ipoa index=5 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_ipoa index=6 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_ipoa index=7 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_ethoa index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_ethoa index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_ethoa index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_ethoa index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_ethoa index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_ethoa index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 encaps $19 fcs $20 ulp mac"
add name=autopvc_add_ethoa index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_ethoa index=7 command="eth ifadd intf _auto_$1_$2_eth dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_ethoa index=8 command="eth ifattach intf _auto_$1_$2_eth"
add name=autopvc_add_ethoa index=9 command="ip ifadd intf _auto_$1_$2 dest _auto_$1_$2_eth dynamic enabled"
add name=autopvc_add_ethoa index=10 command="ip ifattach intf _auto_$1_$2"
add name=autopvc_delete_ethoa index=0 command="ip ifdetach intf _auto_$1_$2"
add name=autopvc_delete_ethoa index=1 command="ip ifdelete intf _auto_$1_$2"
add name=autopvc_delete_ethoa index=2 command="eth ifdetach intf _auto_$1_$2_eth"
add name=autopvc_delete_ethoa index=3 command="eth ifdelete intf _auto_$1_$2_eth"
add name=autopvc_delete_ethoa index=4 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_ethoa index=5 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_ethoa index=6 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_ethoa index=7 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_ethoa index=8 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_ethoa index=9 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_pppoa index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_pppoa index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_pppoa index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_pppoa index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_pppoa index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_pppoa index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 encaps $19 fcs $20 ulp ppp"
add name=autopvc_add_pppoa index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_pppoa index=7 command="ppp ifadd intf _auto_$1_$2 dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_pppoa index=8 command="ppp ifattach intf _auto_$1_$2"
add name=autopvc_add_pppoa index=9 command="nat ifconfig intf _auto_$1_$2 translation enabled"
add name=autopvc_delete_pppoa index=0 command="ppp ifdetach intf _auto_$1_$2"
add name=autopvc_delete_pppoa index=1 command="ppp ifdelete intf _auto_$1_$2"
add name=autopvc_delete_pppoa index=2 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoa index=3 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoa index=4 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_pppoa index=5 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_pppoa index=6 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_pppoa index=7 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_add_pppoe index=0 command="atm qosbook ctdadd name _auto_$1_$2_tx conformance $3 peakrate $4 sustrate $5 maxburst $6 minrate $7 maxframe $8 celldelay $9 realtime $10 dynamic enabled"
add name=autopvc_add_pppoe index=1 command="atm qosbook ctdadd name _auto_$1_$2_rx conformance $11 peakrate $12 sustrate $13 maxburst $14 minrate $15 maxframe $16 celldelay $17 realtime $18 dynamic enabled"
add name=autopvc_add_pppoe index=2 command="atm qosbook add name _auto_$1_$2 txctd _auto_$1_$2_tx rxctd _auto_$1_$2_rx dynamic enabled"
add name=autopvc_add_pppoe index=3 command="atm phonebook add name _auto_$1_$2 addr $1.$2 dynamic enabled maxFwdCPCS_PDU $21 maxBwdCPCS_PDU $22"
add name=autopvc_add_pppoe index=4 command="atm ifadd intf _auto_$1_$2_atm dest _auto_$1_$2 dynamic enabled"
add name=autopvc_add_pppoe index=5 command="atm ifconfig intf _auto_$1_$2_atm qos _auto_$1_$2 encaps $19 fcs $20 ulp mac"
add name=autopvc_add_pppoe index=6 command="atm ifattach intf _auto_$1_$2_atm"
add name=autopvc_add_pppoe index=7 command="eth ifadd intf _auto_$1_$2_eth dest _auto_$1_$2_atm dynamic enabled"
add name=autopvc_add_pppoe index=8 command="eth ifattach intf _auto_$1_$2_eth"
add name=autopvc_add_pppoe index=9 command="ppp ifadd intf _auto_$1_$2 dest _auto_$1_$2_eth dynamic enabled"
add name=autopvc_add_pppoe index=10 command="ppp ifattach intf _auto_$1_$2"
add name=autopvc_add_pppoe index=11 command="nat ifconfig intf _auto_$1_$2 translation enabled"
add name=autopvc_delete_pppoe index=0 command="ppp ifdetach intf _auto_$1_$2"
add name=autopvc_delete_pppoe index=1 command="ppp ifdelete intf _auto_$1_$2"
add name=autopvc_delete_pppoe index=2 command="eth ifdetach intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoe index=3 command="eth ifdelete intf _auto_$1_$2_eth"
add name=autopvc_delete_pppoe index=4 command="atm ifdetach intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoe index=5 command="atm ifdelete intf _auto_$1_$2_atm"
add name=autopvc_delete_pppoe index=6 command="atm phonebook delete name _auto_$1_$2"
add name=autopvc_delete_pppoe index=7 command="atm qosbook delete name _auto_$1_$2"
add name=autopvc_delete_pppoe index=8 command="atm qosbook ctddelete name _auto_$1_$2_tx"
add name=autopvc_delete_pppoe index=9 command="atm qosbook ctddelete name _auto_$1_$2_rx"
add name=autopvc_change_qos index=0 command="atm ifconfig intf $1 qos $2"

[ env.ini ]
set var=CONF_REGION value=---
set var=CONF_PROVIDER value=---
set var=CONF_DESCRIPTION value="Factory Defaults"
set var=CONF_SERVICE value="Routed PPPoE on 0/35 and 8/35"
set var=CONF_DATE value=\"\"
set var=HOST_SETUP value=auto
set var=UPGRADE_URL value=http://www.speedtouch.com/upgrade/upgrade.htm
set var=CONF_TPVERSION value=2.0.0

[ wizard.ini ]

[ snmp.ini ]
config sysContact="Service Provider" sysName="SpeedTouch 510" sysLocation="Customer Premises"
community add index=ROCommunity securityname=ROCommunity communityname=_DEV_7F03079AB8BC2A07

[ phone.ini ]
add name=atm_pvc_0_35 addr=0*35
add name=atm_pvc_8_35 addr=8*35

[ ipqos.ini ]
config dest=atm_pvc_0_35 state=enabled
config dest=atm_pvc_8_35 state=enabled
queue config dest=atm_pvc_0_35 queue=1 ackfiltering=enabled
queue config dest=atm_pvc_8_35 queue=1 ackfiltering=enabled

[ qos.ini ]
config format=bytes
ctdadd name=default conformance=UBR
add name=default txctd=default rxctd=default policing=disabled

[ atm.ini ]
ifadd intf=atm_0_35
ifconfig intf=atm_0_35 dest=atm_pvc_0_35 ulp=mac
ifattach intf=atm_0_35
ifadd intf=atm_8_35
ifconfig intf=atm_8_35 dest=atm_pvc_8_35 ulp=mac
ifattach intf=atm_8_35

[ oam.ini ]
config clp=1 loopbackid=6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a6a
modify port=dsl0 blocking=enabled
modify port=dsl1 blocking=enabled
modify port=atm2 blocking=enabled
modify port=atm3 blocking=enabled
modify port=aal5 blocking=enabled
modify port=atm5 blocking=enabled

[ bridge.ini ]
config age=300 filter=no_WAN_broadcast

[ vlan.ini ]

[ dvm.ini ]
config timeout=90

[ eth.ini ]
ifadd intf=ethoa_0_35
ifadd intf=ethoa_8_35
ifconfig intf=ethoa_0_35 dest=atm_0_35 group=default
ifattach intf=ethoa_0_35
ifconfig intf=ethoa_8_35 dest=atm_8_35 group=default
ifattach intf=ethoa_8_35

[ pptp.ini ]

[ ppprelay.ini ]
ifadd intf=bridge
ifadd intf=ethoa_0_35
ifadd intf=ethoa_8_35

[ dhcspool.ini ]
pool add name=LAN_private

[ label.ini ]
add name=DSCP
add name=Interactive
add name=Management
add name=Video
add name=VoIP
add name=default
modify name=DSCP classification=overwrite defclass=dscp ackclass=defclass
modify name=Interactive classification=increase defclass=8 ackclass=8
modify name=Management classification=increase defclass=12 ackclass=12
modify name=Video classification=increase defclass=10 ackclass=10
modify name=VoIP classification=overwrite defclass=14 ackclass=14 bidirectional=enabled inheritance=enabled
modify name=default classification=increase defclass=default ackclass=prioritize

[ ppp.ini ]
ifadd intf=Internet
rtadd intf=Internet dst=0.0.0.0/0 src=0.0.0.0/0 metric=10
ifconfig intf=Internet dest=RELAY accomp=enabled mru=1492 doddelay=60 dnsmetric=10

[ ip.ini ]
ifadd intf=LocalNetwork dest=bridge
ifconfig intf=loop mtu=65535 group=local
ifconfig intf=LocalNetwork mtu=1500 group=lan linksensing=disabled primary=enabled
ifattach intf=LocalNetwork
config forwarding=enabled redirects=enabled netbroadcasts=disabled ttl=64 fraglimit=64 defragmode=enabled addrcheck=dynamic mssclamping=enabled
config checkoptions=enabled
config natloopback=disabled
ipadd intf=LocalNetwork addr=10.0.0.138/24 addroute=disabled
ipadd intf=LocalNetwork addr=192.168.1.254/24 addroute=disabled
ipconfig addr=192.168.1.254 preferred=enabled primary=enabled
rtadd dst=255.255.255.255/32 gateway=127.0.0.1
rtadd dst=192.168.1.0/24 gateway=192.168.1.254
rtadd dst=10.0.0.0/24 gateway=10.0.0.138
rtadd dst=224.0.0.0/4 intf=LocalNetwork

[ autoip.ini ]

[ ipqosmeter.ini ]

[ autopvc.ini ]
config mode=passive type=bridge overwrite=disabled peakrate=0

[ diagnostics.ini ]
config pingtimeout=1000 pingpacketsize=32

[ dnsc.ini ]
config timeout=5 retry=4 search=enabled
dnsadd addr=127.0.0.1 port=53

[ dnss.ini ]
config domain=lan timeout=15 suppress=0 state=enabled trace=disabled syslog=disabled WANDownSpoofing=enabled WDSpoofedIP=198.18.1.0
host add name=dsldevice addr=0.0.0.0 ttl=1200
host add name=speedtouch addr=0.0.0.0 ttl=1200

[ dhcs.ini ]
debug traceconfig state=disabled
policy verifyfirst=enabled trustclient=enabled
pool config name=LAN_private intf=LocalNetwork poolstart=192.168.1.64 poolend=192.168.1.253 netmask=24 gateway=192.168.1.254 server=192.168.1.254 leasetime=86400

[ dhcr.ini ]
ifconfig intf=LocalNetwork relay=enabled
add addr=127.0.0.1 intf=LocalNetwork giaddr=192.168.1.254

[ dhcc.ini ]
debug traceconfig state=disabled

[ dyndns.ini ]
service modify name=dyndns server=members.dyndns.org port=www-http request=/nic/update updateinterval=2097120 retryinterval=30 max_retry=3
service modify name=statdns server=members.dyndns.org port=www-http request=/nic/update retryinterval=30 max_retry=3
service modify name=custom server=members.dyndns.org port=www-http request=/nic/update retryinterval=30 max_retry=3
service modify name=No-IP server=dynupdate.no-ip.com port=www-http request=/ducupdate.php updateinterval=86400 retryinterval=30 max_retry=3
service modify name=DtDNS server=dtdns.com port=www-http request=/api/autodns.cfm updateinterval=86400 retryinterval=30 max_retry=3
service modify name=gnudip port=www-http

[ expr.ini ]
add name=wan type=intf intfgroup=wan
add name=local type=intf intfgroup=local
add name=lan type=intf intfgroup=lan
add name=tunnel type=intf intfgroup=tunnel
add name=dmz type=intf intfgroup=dmz
add name=guest type=intf intfgroup=guest
add name=private type=ip addr=10.0.0.0/8
add name=private type=ip addr=172.[16-31].*.*
add name=private type=ip addr=192.168.1.0/24
add name=ssdp_ip type=ip addr=239.255.255.250
add name=mdap_ip type=ip addr=224.0.0.103
add name=icmp type=serv proto=icmp
add name=igmp type=serv proto=igmp
add name=ftp type=serv proto=tcp dstport=ftp
add name=telnet type=serv proto=tcp dstport=telnet
add name=http type=serv proto=tcp dstport=www-http
add name=httpproxy type=serv proto=tcp dstport=httpproxy
add name=https type=serv proto=tcp dstport=443
add name=RPC type=serv proto=tcp dstport=135
add name=NBT type=serv proto=udp dstport=netbios-ns
add name=NBT type=serv proto=udp dstport=netbios-dgm
add name=NBT type=serv proto=tcp dstport=netbios-ssn
add name=SMB type=serv proto=tcp dstport=445
add name=imap type=serv proto=tcp dstport=imap2
add name=imap3 type=serv proto=tcp dstport=imap3
add name=imap4-ssl type=serv proto=tcp dstport=585
add name=imaps type=serv proto=tcp dstport=993
add name=pop2 type=serv proto=tcp dstport=pop2
add name=pop3 type=serv proto=tcp dstport=pop3
add name=pop3s type=serv proto=tcp dstport=995
add name=smtp type=serv proto=tcp dstport=smtp
add name=ssh type=serv proto=tcp dstport=22
add name=dns type=serv proto=tcp dstport=dns
add name=dns type=serv proto=udp dstport=dns
add name=nntp type=serv proto=tcp dstport=nntp
add name=ipsec type=serv proto=ah
add name=ipsec type=serv proto=esp
add name=ipsec type=serv proto=udp dstport=ike
add name=ipsec type=serv proto=udp dstport=4500
add name=esp type=serv proto=esp
add name=ah type=serv proto=ah
add name=ike type=serv proto=udp dstport=ike
add name=DiffServ type=serv dscp=!cs0
add name=sip type=serv proto=udp dstport=sip
add name=sip type=serv proto=tcp dstport=sip
add name=h323 type=serv proto=tcp dstport=h323
add name=h323 type=serv proto=udp dstport=h323
add name=h323 type=serv proto=tcp dstport=1718
add name=h323 type=serv proto=udp dstport=1718
add name=h323 type=serv proto=tcp dstport=1719
add name=h323 type=serv proto=udp dstport=1719
add name=dhcp type=serv proto=udp dstport=bootpc
add name=dhcp type=serv proto=udp dstport=bootps
add name=rtsp type=serv proto=udp dstport=rtsp
add name=rtsp type=serv proto=tcp dstport=rtsp
add name=ssdp_serv type=serv proto=udp dstport=1900
add name=mdap_serv type=serv proto=udp dstport=3235
add name=syslog type=serv proto=udp dstport=syslog

[ labelrule.ini ]
chain add chain=rt_user_labels
chain add chain=rt_default_labels
chain add chain=qos_user_labels
chain add chain=qos_default_labels
rule add chain=qos_default_labels index=1 serv=DiffServ log=disabled state=enabled label=DSCP
rule add chain=qos_default_labels index=2 serv=h323 log=disabled state=enabled label=VoIP
rule add chain=qos_default_labels index=3 serv=sip log=disabled state=enabled label=VoIP
rule add chain=qos_default_labels index=4 serv=ah log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=5 serv=esp log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=6 serv=http log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=7 serv=httpproxy log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=8 serv=https log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=9 serv=imap log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=10 serv=imap3 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=11 serv=imap4-ssl log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=12 serv=imaps log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=13 serv=pop2 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=14 serv=pop3 log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=15 serv=pop3s log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=16 serv=smtp log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=17 serv=telnet log=disabled state=enabled label=Interactive
rule add chain=qos_default_labels index=18 serv=dns log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=19 serv=icmp log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=20 serv=ike log=disabled state=enabled label=Management
rule add chain=qos_default_labels index=21 serv=igmp log=disabled state=enabled label=Video
rule add chain=qos_default_labels index=22 serv=rtsp log=disabled state=enabled label=Video
rule add chain=qos_default_labels index=23 name=default srcintf=!wan log=disabled state=enabled label=default

[ sntpc.ini ]
config poll=60 pollpresync=60
config state=disabled

[ adslpots.ini ]
config opermode=multimode maxbitspertoneUS=14 trace=disabled modemoption=00000000000000000000000000000000

[ nat.ini ]
ifconfig intf=Internet translation=enabled
config

[ ipqosef.ini ]

[ connection.ini ]
appconfig application=IP6TO4 trace=enabled
appconfig application=PPTP trace=enabled timeout=300
appconfig application=ESP timeout=900
appconfig application=IKE trace=disabled timeout=900 floating=enabled
appconfig application=SIP trace=disabled timeout=21600 proxy=enabled
appconfig application=JABBER trace=disabled timeout=120
appconfig application=CU/SeeMe trace=enabled
appconfig application=RAUDIO(PNA) trace=enabled
appconfig application=RTSP trace=enabled
appconfig application=ILS timeout=300
appconfig application=H245 timeout=300
appconfig application=H323 trace=enabled
appconfig application=IRC trace=enabled timeout=300
appconfig application=GAME(UDP) trace=enabled timeout=60
appconfig application=LOOSE(UDP) trace=enabled timeout=300
appconfig application=FTP trace=enabled
appconfig application=SIP b2buacomp=disabled
bind application=LOOSE(UDP) port=67-67
bind application=GAME(UDP) port=27010-27011
bind application=JABBER port=15222-15222
bind application=JABBER port=5222-5222
bind application=FTP port=21-21
bind application=IRC port=6660-6669
bind application=H323 port=1720-1720
bind application=ILS port=1002-1002
bind application=ILS port=389-389
bind application=RTSP port=554-554
bind application=RAUDIO(PNA) port=7070-7070
bind application=CU/SeeMe port=7648-7648
bind application=SIP port=5060-5060
bind application=IKE port=500-500
bind application=ESP port=0
bind application=PPTP port=1723-1723
bind application=IP6TO4 port=0
config configchangemode=immediate probes=disabled
debug trace=disabled
timerconfig timer=tcpidle value=900
timerconfig timer=tcpneg value=120
timerconfig timer=tcpkill value=3600
timerconfig timer=udpidle value=65
timerconfig timer=udpkill value=60
timerconfig timer=icmpkill value=60
timerconfig timer=ipidle value=60
timerconfig timer=ipkill value=0

[ upnp.ini ]
config maxage=1800 writemode=full safenat=disabled

[ system.ini ]
settime timezone=+01:00 daylightsaving=disabled geotimezone=26
config upnp=enabled mdap=enabled drst=disabled resetbutton=enabled
config digestauth=enabled defaultconnection=Internet
config dcache=disabled autosave=enabled autosavedelay=10
locale dec_symbol=, group_symbol=. date_separator=- date_format=ddmmyyyy time_format=iso datetime_format=date+time duration_format=dhmmss

[ system_debug.ini ]
autosave trace=disabled

[ system_raccess.ini ]
config secure=enabled port=51003 timeout=20

[ dsd.ini ]
syslog config syslog=unauthorized
intercept config WDSpoofedIP=198.18.1.1 servertimeout=10 connecterrorurl=/cgi/b/ic/connect/ categoryerrorurl=/cgi/b/ic/connect/ monitorintercepturl=/cgi/b/ic/connect/ unauthorizedrequrl=/cgi/b/ic/blocked/ imageredirect=enabled imageredirecturl=/images/spacer.gif alwaysuseip=disabled
debug proxy state=disabled dest=0.0.0.0 port=0
debug recycling state=enabled interval=5 httpidle=1 otheridle=12
config state=disabled

[ hostmgr.ini ]
config state=enabled scantime=30 autosave=disabled trace=disabled
add mac_addr=00:13:d4:df:fc:47 ip_addr=192.168.1.2 name=Unknown-00-13-d4-df-fc-47 type=generic_device ipintf=LocalNetwork

[ mlp.ini ]

[ mlpuser.ini ]
add name=Administrator password=_CYP_d41d8cd98f00b204e9800998ecf8427e role=Administrator hash2=a2e279ed6671666bed7738338c8c849f defuser=enabled
add name=tech password=_CYP_025bbd63d60366497046c00cc64bc6c3 role=TechnicalSupport hash2=64c437a0cfc135f30d640c2644841a55 defremadmin=enabled

[ servmgr.ini ]
ifadd name=PPTP group=lan
ifadd name=HTTP group=lan
ifadd name=HTTPs group=lan
ifadd name=FTP group=lan
ifadd name=TELNET group=lan
ifadd name=DNS-S group=lan
ifadd name=SSDP group=lan
ifadd name=SNMP_AGENT group=lan
ifadd name=MDAP group=lan
ifadd name=PING_RESPONDER group=lan
modify name=PPTP state=enabled
modify name=DNS-C state=enabled
modify name=SNTP state=disabled
modify name=HTTP state=enabled
modify name=HTTPs state=enabled
modify name=FTP state=enabled
modify name=TELNET state=enabled
modify name=DNS-S state=enabled
modify name=DHCP-S state=enabled
modify name=SSDP state=enabled
modify name=SNMP_AGENT state=disabled
modify name=MDAP state=enabled
modify name=PING_RESPONDER state=enabled
mapadd name=HTTP port=www-http
mapadd name=HTTPs port=443
mapadd name=HTTPI intf=LocalNetwork port=www-http
mapadd name=HTTPI intf=LocalNetwork port=1080
mapadd name=HTTPI intf=LocalNetwork port=httpproxy
mapadd name=FTP port=ftp
mapadd name=TELNET port=telnet
mapadd name=DNS-S port=dns
mapadd name=SSDP port=1900
mapadd name=SNMP_AGENT port=snmp
mapadd name=MDAP port=3235

[ service.ini ]

[ fwlevel.ini ]
add name=BlockAll index=1 readonly=enabled udptrackmode=strict service=disabled proxy=disabled text="Use this Security Level to block all traffic from and to the Internet. Game & Application sharing is not allowed by the firewall."
add name=Standard index=2 readonly=enabled udptrackmode=loose service=enabled proxy=enabled text="Use this Security Level to allow all outgoing connections and block all incoming traffic. Game & Application sharing is allowed by the firewall.."
add name=Disabled index=3 readonly=enabled udptrackmode=loose service=enabled proxy=enabled text="Disable the firewall. All traffic is allowed to pass through your SpeedTouch. Game & Application sharing is allowed by the firewall."
set name=Disabled

[ firewall.ini ]
config state=enabled keep=disabled tcpchecks=exact udpchecks=enabled icmpchecks=enabled logdefault=disabled logthreshold=enabled tcpwindow=65536
rule add chain=source_fire index=1 name=AnyTraffic log=disabled state=enabled action=accept
rule add chain=forward_level_BlockAll index=1 name=AnyTraffic log=disabled state=enabled action=drop
rule add chain=forward_level_Standard index=1 name=FromLAN srcintf=lan log=disabled state=enabled action=accept
rule add chain=forward_level_Disabled index=1 name=AnyTraffic log=disabled state=enabled action=accept

[ endofarch ]

[jutta]

> set var=CONF_SERVICE value="Routed PPPoE on 0/35 and 8/35"
..
>[ phone.ini ]
>add name=atm_pvc_0_35 addr=0*35
>add name=atm_pvc_8_35 addr=8*35

die kann mit etwas glueck fuer einen entbuendelten inode-anschluss passen (vergl. http://xDSL.at/new/viewtopic.php?t=30605 ) oder auch fuer einen entbuendelten uta-anschluss, aber sicher nicht fuer adsl von ta oder einem ta-reseller.

kannst du dich noch erinnern, woher du die firmware hattest? vielleicht gibt es dort user.inis, die man abwandeln koennte.

[Wooschli]

so und nun? wie soll ich nun weiter machen?

[Bender]

so und nun? wie soll ich nun weiter machen?

• Enweder zurückkehren auf Multiuser (was ohnehin das Sichere und Bessere ist)
• oder auf die ältere und angeblich funktioniert habende F/W zurückgehen. (Da auf dem ST510 die Vorgänger-F/W aufgespielt war, ist davon auszugehen, dass nach einem Factory reset das Wiedereinspielen der älteren F/W auch über den Wizard möglich sein wird.) Wenn das geschehen ist, geht's — zurück auf Square One — wie schon beschrieben weiter.

[Wooschli]

nein wie schon anfangs beschrieben bekomm ich die alte Firmware nicht mehr auf das Modem. beim downgraden bekomm ich immer eine fehlermeldung dass das Modem nicht mehr verfügbar sei. und leider weiß ich nicht wie man einen *.bin Datei händisch ins Modem spielen kann.

[Bender]

Hiya, die Fehlermeldung, dass das Modem nicht mehr verfügbar sei, weist eher auf einen Verbindungsfehler hin.

Falls nicht ohnehin gemacht:

• ST510 von der ADSL-Leitung nehmen
• ST510 an PC hängen
• PC-Interface auf 10.0.0.140, s/n 255.255.255.0, g/w 10.0.0.138 benamsen
• ST510 hard rebooten
• PC rebooten
• >10.0.0.138: Check der F/W-Version
• allenfalls neuer Wizard-Versuch - oder anstelle dessen: die von mir gelinkte .ini uploaden
• IP bei PC-Interface wieder auf automatisch stellen

[Wooschli]

Hallo zusammen!

Habe es geschaft. ST510 kann wieder als normales Modem verwendet werden.
Erkläre nun genau wie ichs gemacht habe:

Benötigt wird: die Firmware R 4.2.7
Herunter zu laden unter
http://www.speedtouch.net.nz/510seriesFirmware.htm


1. ST510 von der ADSL-Leitung nehmen

2. ST510 resetten (Factory Default)

3. Modem ausschalten

4. PC Netzwerk IP: 10.0.0.10
Sub: 255.255.255.0
alles andere leer lassen

5. Modem einschalten und auf dem Einschlatknopf draufbleiben
und ca 6-12 sec. warten.
Modem sollte im Aktualisierungsmodus gestartet haben.
Lämpchen: Netzwerk = Grün, @ = blickt Orange

6. So und nun muss es schnell gehn.
Es sind max. 2 Minuten Zeit: Die zuvor heruntergeladene Datei
"ST500 series R4.2.7G and upgrade wizard.exe" starten und
der Installationsanweisung folgen.

7. Nach neu Start von ST510 die orginal CD einlegen und die Config
von AON wieder reinspielen.


Nun sollte einen normale VPN Verbindung wieder möglich sein.

Gefunden hab ich das unter der URL http://speedtouch.net.nz/forum/topic.asp?TOPIC_ID=491

Hoffe dass ich es verständlich erklärt habe.

Gruß Wooschli

[wernerkl]

beim 510er gibts aber auch was einfacheres um es zurückzusetzten wurde hier schon mal beschrieben, dazu braucht man nur die taste vorne mitte!

[Bender]

 
         Bubi, Bubi, noch einmal ...

[Wooschli]

nei @wernerkl der knopf vorne stellt lediglich die Factory defaults von der aktuellen Firmware wieder her und diese kann nicht für aon ppptp einwahl verwendet werden.

und nun zu Blender. erstens bin ich kein BUBi und zweitens hab ich mich nur falsch ausgedrückt. meinte natürlich von der telefonleitung nehmen aber wer helfen will wird halt noch bestraft, BUBI BUBI. das hat man halt davon.

thats it!!!

[Bender]

Blender @ Wooschi

Mein Bildbeitrag bezieht sich auf die Tatsache, dass die von Dir gepriesene Zeile von meinem unmittelbar vorangegangen Posting übernommen, also noch einmal verwendet wurde.

Die Caption nimmt in Anbetracht dieser arglosen Wiederholung Anleihe beim Titel (Kursive) eines der Hits des Münchner Oktoberfests.

NB:

Zur Buße gibt’s bei der heurigen Wiesn nur eine viertel Portion Mastente.