xDSL.at

von **bene** » Di 25 Dez, 2001 14:24

Hallo,
Bei mir ist folgendes vorgefallen:
Ich hab SuSE 7.2. Der ADSL-Zugang hat schon wunderbar geklappt, bis zu dem Zeitpunkt andem ich mich dazu entschlossen habe das Systm neu, mit allen Paketen aufzusetzen.
Konfiguration ist genau wie vorher, ich hab auch die selbe pptp Binary verwendet.
Aber anstatt zu verbinden schreibt er eine Seite fuer mich unverstaendliches Zeug.
Habe es auch mit einer neu kompilierten Source versucht -> selbes Ergebnis.
Was ist da los?
bene

von **Manuel Capellari** » Di 25 Dez, 2001 14:41

>anstatt zu verbinden schreibt er eine Seite fuer mich unverstaendliches Zeug
für dich unverständlich, für andere vielleicht sehr aufschlussreich ...
... welche fehlermeldung bekommst du?

>Habe es auch mit einer neu kompilierten Source versucht -> selbes Ergebnis.
was hast du neu kompiliert?

von **bene** » Di 25 Dez, 2001 14:47

<HTML>Hallo,
Kompiliert hab ich die Teile, die dann das pptp werden.
Fehlermeldungen:

root@linux:/home/bene > pptp alcatel
using channel 3
Using interface ppp0
Connect: ppp0 <--> /dev/pts/2
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xd526896f> <pcomp> <accomp>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xd526896f> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x28 <auth chap MD5> <magic 0x73c75618>]
sent [LCP ConfAck id=0x28 <auth chap MD5> <magic 0x73c75618>]
rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0xd526896f> <pcomp> <accomp>]
sent [LCP EchoReq id=0x0 magic=0xd526896f]
cbcp_lowerup
want: 2
rcvd [CHAP Challenge id=0x9e <6b0b5f7441982ab80fdf59db6a235c64>, name = "WHEBIS01"]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
rcvd [LCP EchoRep id=0x0 magic=0x73c75618]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [LCP EchoReq id=0x1 magic=0xd526896f]
rcvd [LCP EchoRep id=0x1 magic=0x73c75618]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
sent [LCP EchoReq id=0x2 magic=0xd526896f]
rcvd [LCP EchoRep id=0x2 magic=0x73c75618]
sent [CHAP Response id=0x9e <bea30f2e1c3b46625353dcff0d2e2a4e>, name = "[email protected]"]
rcvd [CHAP Failure id=0x9e "Authentication failure"]
Remote message: Authentication failure
CHAP authentication failed
cbcp_lowerdown
sent [LCP TermReq id=0x2 "Failed to authenticate ourselves to peer"]
rcvd [LCP TermReq id=0x29]
sent [LCP TermAck id=0x29]
rcvd [LCP TermAck id=0x2]
Connection terminated.
Couldn't release PPP unit: Inappropriate ioctl for device</HTML>

von **Manuel Capellari** » Di 25 Dez, 2001 14:50

wie schaut denn deine /etc/ppp/options aus?

bzw. welche pppd version hast du drauf?

von **bene** » Di 25 Dez, 2001 15:22

<HTML>Hallo,
tut mir leid, dass das so lange gedauert hat.
wie finde ich die Version von pppd raus?

# /etc/ppp/options
#
# Not every option is listed here, see man pppd for more details.
# This file is read by the pppd,
# it is an error when it is not present.
#
# use the following command to see the active options:
#
# grep -v ^# /etc/ppp/options | grep -v ^$
#

# ---<Start of File>---
# The name of this server. Often, the FQDN is used here.
#name <host>

# Enforce the use of the hostname as the name of the local system for
# authentication purposes (overrides the name option).
#usehostname

# If no local IP address is given, pppd will use the first IP address
# that belongs to the local hostname. If "noipdefault" is given, this
# is disabled and the peer will have to supply an IP address.
#noipdefault

# With this option, pppd will accept the peer's idea of our local IP
# address, even if the local IP address was specified in an option.
#ipcp-accept-local

# With this option, pppd will accept the peer's idea of its (remote) IP
# address, even if the remote IP address was specified in an option.
#ipcp-accept-remote

# Run the executable or shell command specified after pppd has terminated
# the link. This script could, for example, issue commands to the modem
# to cause it to hang up if hardware modem control signals were not
# available.
# If mgetty is running, it will reset the modem anyway. So there is no need
# to do it here.
#disconnect "chat -- \d+++\d\c OK ath0 OK"

# Increase debugging level (same as -d). The debug output is written
# to syslog LOG_LOCAL2.
debug

# Enable debugging code in the kernel-level PPP driver. The argument n
# is a number which is the sum of the following values: 1 to enable
# general debug messages, 2 to request that the contents of received
# packets be printed, and 4 to request that the contents of transmitted
# packets be printed.
#kdebug n

# noauth means do not require the peer to authenticate itself, this must
# be set if you want to use pppd to connect to the internet. In this case
# *you* must authenicate yourself to the peer(internet provider), so do
# not disable this setting unless you are the dial-in server which where
# the peer has to autenticate to.
noauth

# Use hardware flow control (i.e. RTS/CTS) to control the flow of data
# on the serial port.
crtscts

# Specifies that pppd should use a UUCP-style lock on the serial device
# to ensure exclusive access to the device.
lock

# Use the modem control lines.(is default)
modem
# The opposite: local
#
# Description:
# Don't use the modem control lines. With this
# option, pppd will ignore the state of the CD (Car
# rier Detect) signal from the modem and will not
# change the state of the DTR (Data Terminal Ready)
# signal.
#
# You need to disable modem and enable local if you want to connect
# to anoter system without using a modem:
#local

# async character map -- 32-bit hex; each bit is a character
# that needs to be escaped for pppd to receive it. 0x00000001
# represents '\x01', and 0x80000000 represents '\x1f'.
# To allow pppd to work over a rlogin/telnet connection, ou should escape
# XON (^Q), XOFF (^S) and ^]: (The peer should use "escape ff".)
#asyncmap 200a0000
asyncmap 0

# needed for some ISDN Terminaladaters, namely ELSA, those seem to have
# problems with asyncmap negotiation, so you can turn off this procedure
# in case your ISDN box has trouble with it, by enabling this option.
# You have to disable the asyncmap <x> option to be sure to have it
# active. If you use wvdial, set the ISDN parameter in /etc/wvdial.conf
# instead.
#default-asyncmap

# Set the MRU [Maximum Receive Unit] value to <n> for negotiation. pppd
# will ask the peer to send packets of no more than <n> bytes. The
# minimum MRU value is 128. The default MRU value is 1500. A value of
# 296 is recommended for slow links (40 bytes for TCP/IP header + 256
# bytes of data).
#mru 542

# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer
# requests a smaller value via MRU negotiation, pppd will request that
# the kernel networking code send data packets of no more than n bytes
# through the PPP network interface.
#mtu <n>

# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot"
# notation (e.g. 255.255.255.0).
#netmask 255.255.255.0

# Don't fork to become a background process (otherwise pppd will do so
# if a serial device is specified).
nodetach

# If this option is given, pppd will send an LCP echo-request frame to
# the peer every n seconds. Under Linux, the echo-request is sent when
# no packets have been received from the peer for n seconds. Normally
# the peer should respond to the echo-request by sending an echo-reply.
# This option can be used with the lcp-echo-failure option to detect
# that the peer is no longer connected.
lcp-echo-interval 30

# If this option is given, pppd will presume the peer to be dead if n
# LCP echo-requests are sent without receiving a valid LCP echo-reply.
# If this happens, pppd will terminate the connection. Use of this
# option requires a non-zero value for the lcp-echo-interval parameter.
# This option can be used to enable pppd to terminate after the physical
# connection has been broken (e.g., the modem has hung up) in
# situations where no hardware modem control lines are available.
lcp-echo-failure 4

# Send up to 60 LCP configure-request during negotiation. With a value
# of 2 for lcp-restart below, this might take up to 2 minutes.
lcp-max-configure 60

# Resend unanswered LCP requests after 2 seconds.
lcp-restart 2

# Specifies that pppd should disconnect if the link is idle for n seconds.
idle 600

# Specifies the maximal number of attempts to connect to the server. This
# is useful for dial on demand. Default value is 10.
#maxfail 3

# Disable the IPXCP and IPX protocols.
noipx

#-------------------------------------------------------------------------
# The next two options are only interesting for you if you are admin of
# a system with other users that use ppp, and those users are normally
# never allowed to add default route, or you do not want users to
# replace the default route.
#-------------------------------------------------------------------------

# enable this to prevent users from attempting to add a default route.
# Use this option with caution: If the user needs to use a program like
# wvdial, he will not be able to connect because wvdial forces defaulroute
# but this is rejected by this option and the user will not be able to
# connect to the internet.
#nodefaultroute

# enable this to prevent users from replacing an existing default route.
#noreplacedefaultroute

#-------------------------------------------------------------------------
# All options below only make sense if you configure pppd to be a dial-in
# server, so don't touch these if you want dial into your provider with
# PPP!
#-------------------------------------------------------------------------

# Set the assumed name of the remote system for authentication purposes
# to <n>.
#remotename <n>

# Add an entry to this system's ARP [Address Resolution Protocol]
# table with the IP address of the peer and the Ethernet address of this
# system. {proxyarp,noproxyarp}
#proxyarp

# Use the system password database for authenticating the peer using
# PAP. Note: mgetty already provides this option. If this is specified
# then dialin from users using a script under Linux to fire up ppp wont work.
#login

# Specify which DNS Servers the incoming Win95 or WinNT Connection should use
# Two Servers can be remotely configured
#ms-dns 192.168.1.1
#ms-dns 192.168.1.2

# Specify which WINS Servers the incoming connection Win95 or WinNT should use
#ms-wins 192.168.1.50
#ms-wins 192.168.1.51

# ---<End of File>---
#
# Not every option was listed here, see man pppd for more details.
# This file is read by the pppd,
# it IS an error when it is NOT present.
#
# use the following command to see the active options:
#
# grep -v ^# /etc/ppp/options | grep -v ^$
#

noipdefault
name "[email protected]"
noauth
defaultroute

lcp-echo-failure 10
lcp-echo-interval 10</HTML>

von **Manuel Capellari** » Di 25 Dez, 2001 16:06

>wie finde ich die Version von pppd raus?
pppd -v

änder deine /etc/ppp/options mal auf folgende um:
<b>
debug
noipdefault
name TEILNEHMERKENNUNG
noauth
defaultroute
persist
</b>

hth

von **bene** » Di 25 Dez, 2001 22:33

Hallo,
ich bin ein VOLL id**t, hab den Benutzernamen falsch geschrieben!!
tut mir leid.
bene

xDSL.at

SuSE Komplettinst.

SuSE Komplettinst.

RE: SuSE Komplettinst.

RE: SuSE Komplettinst.

RE: SuSE Komplettinst.

RE: SuSE Komplettinst.

RE: SuSE Komplettinst.

RE: SuSE Komplettinst.

Wer ist online?